Power supply wiring issues *– New 02/10/03*

It seems like this subject is always coming up on the MOTM list. What size wire should

I use to add another PCB to my MOTM-900? Or, what size wire should I use between

my case style power supply and the 900 series distribution PCBs? I plan to do a

complete page on this very subject soon. However, for now, I am posting an e-mail

I sent to the list with the Ohm’s law justification for using larger wire for this connection.

Please see the attached PDF file or the drawing in this document as I refer to it in this discussion. In this drawing, I will assume that the power supply has a regulator which is regulating to the power supply voltage at the power supply and not making use of remote sensing. Some modules (in particular that ones that have LEDs) vary in the current that they draw from the power supply. Other modules are somewhat sensitive to fluctuations in power supply voltage. Let's take one of each for this example. |

Ohm's law tells us that anytime we have current flow across resistance, we have voltage drop. We

know that all the components of our power supply wiring have resistance. We are going to look at

ONLY the resistance of the wire. If we look at the drawing, we can assume that the voltage at the

PCB is lower than the voltage at the power supply by this amount:

E drop (wire A) = I (module left) + I (module right) x R (wire A).

The voltage at each module is also lower than the voltage at the PCB by this amount:

Module left:

E drop (wire B) = I (module left) x R (wire B)

Module right:

E drop (wire C) = I (module right) x R (wire C)

To find the voltage drop in the wiring to each module from the point of regulation (the power supply),

we have to add the voltage drops:

For module left total drop from the power supply:

E drop (wire A) + E drop (wire B)

For module right total drop from the power supply:

E drop (wire A) + E drop (wire C)

About now, you are probably cursing me for stating the obvious. But, I wanted it to be clear that current

from one module effects the voltage delivered to a different module.

See that voltage drop to module right = [I (right) + I (left) x R (wire A)] + [I (right) x R (wire C)]

And, varying current produces varying voltage drops. So, in our example, we see that varying load in

module left is causing varying voltage to be delivered to module right. That is going to occur, no matter

what we do with wiring. Our task is to minimize that to a negligible amount.

Since we have only 2 modules in the drawing, I am going to put some out-of-proportion numbers in

the formula to make a point.

module left I minimum = 20 mA; maximum = 50mA

module right I = constantly around 30 mA

Voltage (+15) we will look at only one leg

resistance wire A, B and C all = 2 ohms

Voltage at PCB (I left min) = 15 - [(0.02 + 0.03) x 2] = 14.9 volts

Voltage at module left = 14.9 - (0.02 x 2) = 14.86

Voltage at module right = 14.9 - (0.03 x 2) = 14.84

Voltage at PCB (I left max) = 15 - [(0.05 + 0.03) x 2] = 14.84 volts

Voltage at module left = 14.84 - (0.05 x 2) = 14.74

Voltage at module right = 14.84 - (0.03 x 2) = 14.78

Delta E module left = .12 volts (.08%)

Delta E module right = .06 volts (.04%) 50% of delta E (left)

So, even though module right has a constant load, it is seeing a fluctuating supply voltage because of the

varying voltage drop across wire A caused by the varying load of module left. The problem is that wire A,

B and C all have the same resistance. So, voltage drop from each module is imposed equally across its

own power cable and the power cable that supplies the PCB (wire A in this case).

The solution, is to lower the resistance of wire A so that a larger percentage of the varying voltage drops

is found across the individual module power supply wire. Interaction between modules is then reduced.

Let's change the resistance of wire A from 2 ohms to 2/10 ohm and look at these numbers again:

Voltage at PCB (I left min) = 15 - [(0.02 + 0.03) x 0.2] = 14.99 volts

Voltage at module left = 14.99 - (0.02 x 2) = 14.95

Voltage at module right = 14.99 - (0.03 x 2) = 14.93

Voltage at PCB (I left max) = 15 - [(0.05 + 0.03) x 0.2] = 14.984 volts

Voltage at module left = 14.984 - (0.05 x 2) = 14.884

Voltage at module right = 14.984 - (0.03 x 2) = 14.924

Delta E module left = .066 volts (.044%)

Delta E module right = .006 volts (.004%) 9% of delta E module left

Notice how lowering the resistance of the wire A has reduced the delta E to module right caused by the

varying load of module left. Or, to say it more easily, module interaction due to power supply coupling has

been reduced. Now, these numbers are a little out of whack as the resistance of our power wires was

exaggerated some to make a point.

But, now we see the importance of using LARGE wire between the power supply and the distribution

PCBs. This wire should represent the smallest portion of resistance in the wiring between the power

supply and the module. I always use # 12 or 14.

This question comes up frequently, and I hope this helps someone understand why the wire to the distribution point has to be sized for something other than it loadability.